[Offer] Gigabyte GA-Z97X-Gaming 3 rev 1.1 Bios F8G with ReBAR

Hello everyone,

I am sharing my custom modified BIOS F8G for the GIGABYTE GA-Z97X-Gaming 3 (Rev 1.1) motherboard. This build updates the legacy Haswell platform with modern hardware security standards, native PCIe Resizable BAR support, and the final structural microcode updates.

BIOS Details & Internal Module Versions

  • Motherboard Model: GIGABYTE GA-Z97X-Gaming 3

  • Base Firmware Version: F8g (Beta BIOS)

  • Flashing Requirement: No special tools needed—this modified image can be flashed normally and safely directly through GIGABYTE’s built-in Q-Flash utility.

Audited Module Status:

  • Storage / RAID: :laptop:

    • EFI Intel RST for SATA - 13.5.0.2164

    • OROM Intel RST for SATA - 13.5.0.2164

    • EFI NVMe Driver Present (Native Boot Support)

  • Video OnBoard: :laptop:

    • EFI GOP Driver HSW-BDW - 5.5.1034

    • RAW GOP VBT HASWELL - 189

    • OROM VBIOS HSW-BDW - 1038

  • Network: :wireless:

    • EFI Lx Killer Undi - 1.1.0.13

    • OROM Lx Killer E2xxx - 2.1.1.5

    • Intel Management Engine: 9.1.25.1005

Modifications Applied :

1. Resizable BAR Native Integration :check_box_with_check:

2. Above 4G Decoding Unlocked :check_box_with_check:

  • Explicitly exposed and enabled the native “Above 4G Decoding” option within the BIOS menus to allow proper 64-bit memory mapping allocations.

3. Secure Boot & TPM 2.0 Support :check_box_with_check:

  • Added the modern Microsoft Windows Production CA 2023 KEK (Key Exchange Key) to the Secure Boot database, ensuring seamless synchronization with modern Windows operating systems.

  • Full native TPM 2.0 support ( SLB9665)

4. CPU Microcode Updates :check_box_with_check:

  • Updated the CPU container block with the latest available 2019 microcodes for the Haswell architecture.

Test System Specs & Verification :laptop:

  • CPU: Intel Core i5-4690K (Haswell-Refresh)

  • RAM: 16 GB DDR3 Dual-Channel

  • GPU: AMD Radeon RX 7600 8GB VRAM

  • OS: Windows 11 / Fedora 44 Linux (Full 64-bit address space verified via lspci with [size=8G] allocation window).

Instructions for Use

  1. Copy the modified BIOS file to a FAT32-formatted USB drive.

  2. Reboot, enter your BIOS setup, and open Q-Flash to flash the file directly.

  3. After flashing, ensure Above 4G Decoding is enabled, and CSM is completely Disabled (Pure UEFI Mode).

  4. Once booted into your operating system, download and run the command-line helper utility from GitHub: ReBarState.exe.

  5. Enter your desired allocation exponent (e.g., 11 for 2GB, 12 for 4GB, or 13 For 8GB, write the variable to NVRAM, then reboot.

Download Link: https://drive.google.com/file/d/1azSL_t1xUgeaPd6s0BM4Yyr2irZRkSFJ | Mirror

NOTE: There are 2 files, original and modified, inside the zip archive. Original is supplied from Gigabyte eSupport and has only above4g unlocked and KEK CA 2023 updated. ReBAR mod has all the stuff mentioned above ( new drivers and microcodes updated)

Disclaimer: As with all custom BIOS mods, flash at your own risk. This image works flawlessly on my hardware setup, but always ensure your backup recovery workflows are in place before proceeding.

1 Like

@Mixa94 Was about to submit, but i think you’ve got it :joy:

Anyways, here you go if you want to test, i kept the bios structure intact: Z97XGaming3_Complete.rar (5.6 MB)

This one has both Rebar and NvStrapsRebar, and updated the Intel ME to 9.1.40.1000 (rebuilt using IntelFIT, so it’s not the same as FWUpd results). I re-did it many times to keep everything (the padding files) intact :rofl:

These are the patches thaat i’ve applied (mostly on Runtime, PciBus, PciHostBridge, and NBPei)

Can you just make a better post that is different from my version of the actual changelog, so if someone comes here and knows what is better or what is downloading.

I also want to say here that I am experiencing sleep and shutdown problems no matter what bios version; that’s why I started looking for bios modding in the first place… looks like sleep and shutdown work on Win11 for now, but on Linux it is always present, and ACPI is throwing a lot of errors since I got this RX7600 card last year, but this is diffrent story

Having 2 posts of the same thing was not a thing here, mods usually would just merge the post and renamed the original post onto something new, hence i adhere to your request on your original post; to move it here.

The difference i could say minimal compared to your version (probably?). Basically i did almost the same as your bios (i didn’t take a look on your bios yet), with the difference was the ME FW was updated, and if visible, the invisible menu below Access Level might be accessible. I do always keep the bios structure intact, hoping to not caused issues whatsoever, so yeah it’s a combination of manual edit and automated like using UBU, but im more on the manual side to make sure it is safe to flash (hencr why it took me some time to find a way to keep the padding files present and unaltered).

Feel free to test my bios if you want, and send your feedback here. You can use the bios mod i’ve sent here to update your bios mod post :). I strongly recommend to post the bios mod and the original bios F8g directly by uploading a .rar of it, rather than keep it hosted in google drive because who knows the link might die later on, and if it was uploaded directly to this forum in your post, it’ll stay there as long as the forum is alive :slight_smile:

For sleep, i guess you could turn on ErP and see if it helps.

For sleep, i guess you could turn on ErP and see if it helps.

ErP should be enabled, but it does not matter whether it is on or off; the same thing happens.
@Koekieezz

Can you teach me how to update Intel ME in the BIOS file?

Where to get proper intel FIT tools, etc.? Is it difficult to modify the ME area?

1 Like

If you do need that sleep function under linux, i think you should re-ask gigabyte for a fixed ACPI Sleep under linux with the fixed F8g bios from gigabyte that was sent through you, if you’re sure this is not a linux issue, but acpi ones.

Before you start/after you’ve completed your mod, open the bios file on hex editor like HxD, go to Address 0x40h, the address range should be 0x40h up to 0x45h , and temporarily “fix” the address. You can check the Base Address of the bios using uefitool, in this example, the base address is 200000h:

Which means, in little endian, it is 00 00 02 (CMIIW). Then, you just edit address range on 0x40h up to 0x45h to match you Base Address, like this:

Be aware that the size might varies between bioses, so do you self a favor to open up calculator or manually write it.

After you save it, open the bios with Intel Fit v9.1 (you can get it here), and go to Build → Build Settings → Untick Generate Intermediate Build file, click ok, and go to file → save as, or if you want to enable and/or disable settings in the FIT, do that, and then save as .xml, and exit.

Once you’ve exitted, copy the RGN/Clean EXTR of the ME Target you wish, open the bios name folder that was created automatically after you open the bios with intel fit, go to decomp, and paste it there. Delete ME Region.bin, and rename the ME of your choice.bin onto ME Region. bin. Go back, and open fit again, wait till it loaded completely, and after that you can just open the saved .xml, and after loaded normally, go to Build → Build Image, wait till it finishes, and you’ll get Output.bin in the Build folder inside where the FIT Executables resides in.

Now, grab that output.bin, and revert back the changed bits you did on range 0x40h up to 0x45h (in this case, 00 is the default0, save it, and you’re safe to flash that bios.

Now if you may ask, “Why gigabyte did such thing, instead of correcting the length to the bios length?”, My best guess is: On how Gigabyte Bios might work. So basically, when the Bios Region in the descriptor are set at 00, it means the whole bios IS the bios image, hence flashing it to the whole spi, where as if you set/correct/fix it to the actual base address of the bios in that part, it might only flashes the bios region, and if it happens, when the backup bios is also updated, it only flashed the bios region instead of the whole region (i mean it, the spi, erased, and then written with the bios region only, leaving the rest unwritten as FF’s). I learned it the hard way (gotta desolder the M_Bios lol). Maybe it’s how their dualbios work.

@Koekieezz can you check / update Intel ME on my latest mod : i just updated storage drivers from 13.5xx series to 14.8xx and OROM VBIOS, ReBAR module is also present

Disk Controller :
EFI Intel RST RAID Driver - 14.8.2.2397
OROM Intel RST for SATA - 14.8.2.2397
Video OnBoard :
EFI GOP Driver HSW-BDW - 5.5.1034
RAW GOP VBT HASWELL - 189
OROM VBIOS HSW-BDW - 1044

mod_Z97XGAMING3#2.zip (5.6 MB)

Now everything looks in order just intel ME is older 9.1.25 but can be manualy flashed/updated from win11.

Speaking of sleep/shootdown problem its specific behavior, everytime i go out from home i unplung PC from wall socket so pc is unpowered for several hours and when its pluged back to power behaves normaly and after some time of usage begins to trohow these ACPI errors in practicular : ACPI BIOS Error (bug): Could not resolve symbol [\_GPE._L09.D1F0], AE_NOT_FOUND

Acording to gemini AI and suggest DSDT patching :

When you plug in your AMD RX 7600, it populates a specific path on the PCIe bus. When the system shifts power states (sleep or shutdown), it fires General Purpose Event _L09.

The motherboard’s factory ACPI code jumps to a method named _L09 to process the event, and inside that method, it blindly tries to talk to a device component called D1F0. However, because D1F0 doesn’t exist or isn’t properly declared in the motherboard’s static ACPI tables for this hardware configuration, the execution immediately crashes with AE_NOT_FOUND.

Because the method crashes halfway through execution, it never clears the hardware interrupt line. The motherboard is trapped in a permanent hardware loop, spamming thousands of interrupts a second, which Linux registers as a constant wake command.

Before this RX7600 card i had RX560 with 4Gb VRAM and everything worked fine.

I dont see rebar working with 5500XT and Z97XGaming3_Complete.rar

@traposama after you flashed that bios, disable csm and enable above 4g decoding, boot to windows, and run rebarstate as admin, type value 32, enter, and reboot

1 Like

Thx!!! do you know if how to replace module tpm 1.2 for 2.0 ?

What chip is your tpm module now?

is IFX tpm 1.2 but can convert to 2.0. And the bios is ga-990fx F2

@traposama if what you meant is “how to run tpm 2.0” on GA-990FX, you need to ask gigabyte eSupport for it. You could add some request to them, such as:

  1. Adding Above 4G Decoding Function
  2. Add TPM 2.0 Support
  3. Update the Secure Boot keys to 2023 Secure Boot keys

See if they’re able to pull the plug. Honestly, i never saw an AM3/AM3+ motherboard with uefi bios ran resizable bar under windows, since the above 4g decoding function is absent in most of AM3/AM3+ UEFI Bioses in gigabyte boards (i think most of brands does not have this option, not even hidden).

If Gigabyte eSupport able to provide you with a bios with the mentioned request (Above 4G Decoding, TPM2.0 Support, 2023 Secure Boot Keys), i might try to modify the bios and see how it goes. If the normal mod works, but rebar didn’t work, maybe @Kuri0 might able to help setting up new patches..

Hello!
Interesting features of Z97/
Everything is easier on Z370.
Thank.

Hey!
Any idea if this bios will run on a rev Rev. 1.0. Motherboard ?

Revisions 1.0 and 1.1 uses the same Gigabyte bios.

1 Like

Thanks.

Hi everyone, you’re doing a great job!

Until now, I was running BIOS F8e, but for some time, due to some Windows 11 security updates, my PC would freeze about 5 minutes after booting.

I switched to Z97XGAMING3_FIXED.F8g. Is this the final stable BIOS, or is there another version I should use?

So far, I haven’t had any problems with it, and my PC no longer freezes like it did with F8e.