U-Boot 2009.08 (Mar 13 2015 - 07:57:54) Avocent (0.0.3) EVB CPU: SH-4A BOARD: R0P7757LC00xxRL (Cn step) board BOOT: Secure, HRK generated DRAM: 240MB (240MB of 256MB total DRAM is available on U-Boot) ENV: Using primary env area. In: serial Out: serial Err: serial PCIe: Bridge loaded with 0x18000 bytes WDT2: Booted Lower Vector, 'uboot1' sh_mmcif: 0, sh-sdhi: 1 Net: sh_eth.0, sh_g_eth.0 INFO: 00:002 Start-up -to- util_idrac_main() INFO: 00:004 U-Boot 2009.08 (Mar 13 2015 - 07:57:54) Avocent (0.0.3) EVB INFO: 00:007 U-Boot checkin date(02-20-2015) Version(1.1.26) INFO: 00:006 iDRAC PPID INFO: 00:003 SPI NOR init 4096 KiB MX25L3206E bus=0 cs=0, speed=1000000, mode=3 INFO: 00:007 SH-4A Product: Major Ver=0x31 Minor Ver=0x13 C3 Little endian Family=0x10 Major Ver=0x30 Minor Ver=0x0b INFO: 00:140 BCM54610 OUI=0x00d897 Model=0x26 Revision=0x0a PhyAddr=1 INFO: 00:007 Dedicated monolithic mgmt NIC disabled INFO: 00:004 SD CARD: is not found INFO: 00:043 EMMC: Device: sh_mmcif Manufacturer ID: 90 OEM: 14a Name: HYNIX Tran Speed: 25000000 Rd Blk Len: 512 MMC ver 4.0 HC: Yes cap(<2gb): 0 cap(>2gb): 7569408 ext_rev: 5 rst_n: 0 ext[96]: 0 INFO: 00:023 CPLD: Major Ver=0x1 Minor Ver=0x0 Maint Ver=0x3 Planar: Type=0x03 Rev=0x8 Rework=0x0 Scratch/PathRetry=0x00 PASS: 00:014 Coin cell detected good, AD=0x39b low water=0x2c1 PASS: 00:008 PCIe SH7757_C0 Ver=0.15 MCTP en, CRC=0x8e9b6875 @0x8efbd514 cnt=0x18000 INFO: 00:008 Init PCIe mailbox(PCIe 0xFFEE0150=0x40010000) INFO: 00:006 mode=normal INFO: 00:002 reset_cause=ac PASS: 00:005 Booted Lower Vector, 'uboot1' wdt2cnt=1 INFO: 00:005 wdt0cnt=5 PASS: 00:003 Clear CH1/CH2, clear 4K shared memory@0xffcaa000 on AC power up PASS: 00:007 SMR0 no sermux env, default 0xd4 INFO: 00:004 GRACR=0x3c HISEL=0x00 SIRQCR5_D=0x03 SIRQCR6_D=0x01 LADMSK0=0xff2 MRSTCR0=0xfedffe7f MRSTCR1=0xfff3ff0f MRSTCR2=0x6f80feff BARMAP=0x1 BCR=0x85000000 NCER=0x01fc NCMCR=0x0006 NCCSR=0x0303 INFO: 00:010 Fan logic for monolithic planar type 3 fan1 - def 0000 1fff 3d fan2 - def 0000 1fff 3d fan3 - def 0000 1fff 3d fan4 - def 0000 1fff 3d fan5 - def 0000 1fff 3d fan6 - def 0000 1fff 3d fan7 - def 0000 1fff 3d fan8 - def 0000 1fff 3d INFO: 00:076 Env and backup CRC'ed ok Erasing SPI flash at 0x100000...Writing to SPI flash...done Erasing SPI flash at 0x110000...Writing to SPI flash...done *** no text signature found *** INFO: 01:843 Sync eMMC/SPI NOR/Alternate u-boot images PASS: 00:262 Current u-boot1 1.1.26 verified with 'ubootN1' Trailer Struct - Missing start token, exp=0xc0de1111 rec=0x0 U-boot2 in sync with u-boot1 1.1.26 PASS: 05:577 Verify OS Images N-1: CRC32 OK: Kernel=0xe0ba9419 Rootfs=0xaed59889 PASS: 00:008 Boot device=emmc Boot partition5/N-1 Boot Path Retry:P1/N=0 P5/N-1=0 INFO: 00:071 No 'userexe' defined INFO: 00:000 08:179 Hit any key to stop autoboot: 0 WDT2: Disable in abortboot() OSWDT: Disable in abortboot() CPLD_BMCRDY: Enable BMC_MIN_RDY in abortboot(). Prevent BIOS reset. NOTE: After stopping u-boot in this development mode. You may need to warm/cold reset the server when booting iDRAC manually as BIOS may have already viewed iDRAC as unresponsive. iDRAC8=> ? ? - alias for 'help' base - print or set address offset bdinfo - print Board Info structure boot - boot default, i.e., run 'bootcmd' bootd - boot default, i.e., run 'bootcmd' bootm - boot application image from memory bootp - boot image via network using BOOTP/TFTP protocol cmp - memory compare cp - memory copy crc32 - checksum calculation dhcp - boot image via network using DHCP/TFTP protocol echo - echo args to console erase - erase FLASH memory ext2load- load binary file from a Ext2 filesystem ext2ls - list files in a directory (default /) fatinfo - print information about filesystem fatload - load binary file from a dos filesystem fatls - list files in a directory (default /) flinfo - print FLASH memory information fwu - fwu - firmware upgrade sub-system, type 'help fwu' for details go - start application at address 'addr' help - print online help hrk - Encrypt or decrypt data with AES256-HRK iminfo - print header information for application image itest - return true/false on integer compare loadb - load binary file over serial line (kermit mode) loads - load S-Record file over serial line loady - load binary file over serial line (ymodem mode) loop - infinite loop on address range loopw - infinite write loop on address range md - memory display md5sum - compute MD5 message digest mm - memory modify (auto-incrementing address) mmc - MMC sub system mmcinfo - mmcinfo -- display MMC info mtest - simple RAM read/write test mw - memory write (fill) nfs - boot image via network using NFS protocol nm - memory modify (constant address) ping - send ICMP ECHO_REQUEST to network host printenv- print environment variables protect - enable or disable FLASH write protection ps - ps - persistent storage, type 'help ps' for details rarpboot- boot image via network using RARP/TFTP protocol reset - Perform RESET of the CPU run - run commands in an environment variable saveenv - save environment variables to persistent storage setenv - set environment variables sf - SPI flash sub-system sh_g200 - enable sh-g200 sh_mdio - MDIO of ETHERC/GETHERC setting sleep - delay execution for some time tftpboot- boot image via network using TFTP protocol util - run a Dell developed utility subcommand. version - print monitor version write_mac- write MAC address for ETHERC/GETHERC iDRAC8=> mmc list sh_mmcif: 0 sh-sdhi: 1 iDRAC8=> mmc rescan 1 iDRAC8=> util recover -emmc -from sd -f firmimg.d7 UTIL RECOVER:Transport:sd TargetMMC:EMMC File:firmimg.d7 reading firmimg.d7 110941414 bytes read UTIL RECOVER:SD load passed from FAT fs. UTIL RECOVER:Transport time [sec:mil]: 19:243 Clear OS images in partition/s. Clear kernelN, rootfsN, ubootN 'EMMC' blk size=[0x200][512] Erase to 0xffffffff Mem buf size=[0x06000000][100663296] Total bytes=[0x08000000][134217728] blocks[0x1:0x40001][1:262145] Blocks [0x1:0x30000] Buf[0x88000000]..fill buffer..erase/write Blocks [0x30001:0x40000] Buf[0x88000000]..fill buffer..erase/write Completed loop 1, Elapsed time in hr:min:sec:mil 13:496 Clear kernelN1 'EMMC' blk size=[0x200][512] Erase to 0xffffffff Mem buf size=[0x06000000][100663296] Total bytes=[0x01000000][16777216] blocks[0x40002:0x48002][262146:294914] Blocks [0x40002:0x48001] Buf[0x88000000]..fill buffer..erase/write Completed loop 1, Elapsed time in hr:min:sec:mil 01:506 Clear rootfsN1 'EMMC' blk size=[0x200][512] Erase to 0xffffffff Mem buf size=[0x06000000][100663296] Total bytes=[0x06F80000][116916224] blocks[0x48003:0x7fc03][294915:523267] Blocks [0x48003:0x78002] Buf[0x88000000]..fill buffer..erase/write Blocks [0x78003:0x7fc02] Buf[0x88000000]..fill buffer..erase/write Completed loop 1, Elapsed time in hr:min:sec:mil 10:081 Clear ubootN1 'EMMC' blk size=[0x200][512] Erase to 0xffffffff Mem buf size=[0x06000000][100663296] Total bytes=[0x00080000][524288] blocks[0x7fc04:0x80004][523268:524292] Blocks [0x7fc04:0x80003] Buf[0x88000000]..fill buffer..erase/write Completed loop 1, Elapsed time in hr:min:sec:mil 00:134 *** no text signature found *** *** Updating Partition 1 *** Checking image header CRC ... OK Checking platform env ID..... OK Checking kernel image CRC ... OK Checking rootfs image CRC ... OK Checking u-boot image CRC ... OK Skipping u-boot update ...... NO Checking Platform image CRC . OK Checking processor support .. OK Copying kernel image ........ OK Copying rootfs .............. OK Copying u-boot1 to flash..... OK Copying u-boot2 to flash..... OK Copying u-boot to MMC........ OK Copying platform image ...... OK *** Updating Partition 5 *** Checking image header CRC ... OK Checking platform env ID..... OK Checking kernel image CRC ... OK Checking rootfs image CRC ... OK Checking u-boot image CRC ... OK Skipping u-boot update ...... NO Checking Platform image CRC . OK Checking processor support .. OK Copying kernel image ........ OK Copying rootfs .............. OK Copying u-boot1 to flash..... OK Copying u-boot2 to flash..... OK Copying u-boot to MMC........ OK Copying platform image ...... OK Erasing SPI flash at 0x100000...Writing to SPI flash...done Erasing SPI flash at 0x110000...Writing to SPI flash...done UTIL RECOVER:Program time [sec:mil]:01:18:753 UTIL RECOVER:Total update time [sec:mil]:01:38:000 Re-load 0x1000Kbytes from u-boot offset 0x0 into ILRAM at 0x0 Force Address Error to reset iDRAC U-Boot 2009.08 (May 11 2019 - 03:59:51) Avocent (0.0.3) EVB CPU: SH-4A BOARD: R0P7757LC00xxRL (Cn step) board BOOT: Secure, HRK generated DRAM: 240MB (240MB of 256MB total DRAM is available on U-Boot) ENV: Using primary env area. Undefined env fwu_act Undefined env Failsafe_PowerON_Lockout Undefined env cpld_recover_cnt Undefined env ddr_recover_cnt Restore env FWN= Restore env FWN1= Restore env etherc0= Restore env getherc0= Restore env first_ac=yes Restore env wdt2cnt=1 Restore env ethaddr= Restore env eth2addr= Restore env macs_in_res1=yes Restore env ethact=sh_g_eth.0 Restore env dmn=disabled Restore env wdt0cnt=5 In: serial Out: serial Err: serial WDT2: Booted Lower Vector, 'uboot1' sh_mmcif: 0, sh-sdhi: 1 Net: sh_eth.0, sh_g_eth.0 INFO: 00:002 Start-up -to- util_idrac_main() INFO: 00:005 U-Boot 2009.08 (May 11 2019 - 03:59:51) Avocent (0.0.3) EVB INFO: 00:006 U-Boot checkin date(10-04-2018) Version(1.1.34) INFO: 00:006 iDRAC PPID INFO: 00:003 SPI NOR init 4096 KiB MX25L3206E bus=0 cs=0, speed=1000000, mode=3 INFO: 00:007 SH-4A Product: Major Ver=0x31 Minor Ver=0x13 C3 Little endian Family=0x10 Major Ver=0x30 Minor Ver=0x0b INFO: 00:140 BCM54610 OUI=0x00d897 Model=0x26 Revision=0x0a PhyAddr=1 INFO: 00:007 Dedicated monolithic mgmt NIC disabled INFO: 00:059 SD CARD: Device: sh-sdhi Manufacturer ID: 41 OEM: 3432 Name: SD8GB Tran Speed: 25000000 Rd Blk Len: 512 SD ver 2.0 HC: Yes cap(<2gb): 3436183552 cap(>2gb): 0 ext_rev: 0 rst_n: 0 ext[96]: 0 INFO: 00:063 EMMC: Device: sh_mmcif Manufacturer ID: 90 OEM: 14a Name: HYNIX Tran Speed: 25000000 Rd Blk Len: 512 MMC ver 4.0 HC: Yes cap(<2gb): 0 cap(>2gb): 7569408 ext_rev: 5 rst_n: 0 ext[96]: 0 INFO: 00:023 CPLD: Major Ver=0x1 Minor Ver=0x0 Maint Ver=0x3 Planar: Type=0x03 Rev=0x8 Rework=0x0 Scratch/PathRetry=0x00 PASS: 00:014 Coin cell detected good, AD=0x39b low water=0x2c1 PASS: 00:008 PCIe SH7757_C0 Ver=0.15 MCTP en, CRC=0x8e9b6875 @0x8efbd4ec cnt=0x18000 INFO: 00:008 Init PCIe mailbox(PCIe 0xFFEE0150=0x40010000) INFO: 00:006 mode=normal INFO: 00:002 reset_cause=board PASS: 00:005 Booted Lower Vector, 'uboot1' wdt2cnt=1 INFO: 00:005 wdt0cnt=5 cpld_recover_cnt=0 ddr_recover_cnt=0 PASS: 00:006 SMR0 no sermux env, default 0xd4 INFO: 00:007 Fan logic is not modified on Non-AC power up INFO: 00:053 Env and backup CRC'ed ok *** no text signature found *** INFO: 00:697 Sync eMMC/SPI NOR/Alternate u-boot images PASS: 00:075 Current u-boot1 1.1.34 verified with 'ubootN' Trailer Struct - Missing start token, exp=0xc0de1111 rec=0x0 PASS: 06:981 Verify OS Images N: CRC32 OK: Kernel=0x3fc30fe9 Rootfs=0x90b77173 PData=0x83c2e56c PASS: 00:009 Boot device=emmc Boot partition1/N Boot Path Retry:P1/N=0 P5/N-1=0 INFO: 00:000 08:232 OS_WDT0_EN:180 seconds, Re-load ILRAM: SPI_WP: Not attempted. EMMC_WP: Not attempted. Boot Path Retry:P1/N=0 P5/N-1=0 Copying kernel image ... OK ## Booting kernel from Legacy Image at 88000000 ... Image Name: sh-linux Image Type: SuperH Linux Kernel Image (gzip compressed) Data Size: 3081529 Bytes = 2.9 MB Load Address: 80001000 Entry Point: 80002000 Verifying Checksum ... OK Uncompressing Kernel Image ... OK WDT2: Disable in do_bootm_linux() Monolithic/DRB