Insyde SW Setup Document,,,,

--------------------------------------------------------------------------------------
There are 7 columns composed to one item.
[*],[ID],[Offset],[Width],[Prompt],[Current Value],[All Options],[Help],[CondExpr]

Only one column [Current Value] can be modified, and keep others or it may causes 
unexpected result.
The [Current Value] column is limited by [All Options] column. Users shouldn't give 
a value outside of [All Options] column.

If a '*' presented in first column [*] means if this item may be hidded when condition matched.The last column [CondExpr] shows the condition.
For example:
1. Oneof Type Item:
  {
    *,61d2fffff0394ab9,22,1,Number Lock,off,"Off,On","Select power-on state for Numlock","sif aa=230"
  }
  User can change the 5th ([Current Value]) from Off to On which is one of option in 
  6th column ([All Options]).

2. Numeric Type Item:
  {
    ,61d2fffff0394ab9,23,1,OS Timer Setting,0,"Step=0,Min=0,Max=100","Set BIOS watchdog timer.",""
  }
  User can change the 5th ([Current Value]) form 0 to any value between 0-100 which 
  is limited in 6th column ([All Options]).
--------------------------------------------------------------------------------------
 - Sku ID: [](In hex)
 - Config Name ID: [] 
 - Config ID: [](In hex)
 - BIOS Version(From BVDT): "BayTrail.5.04.48.0056.e"


FormSet Advanced (A04A27F4-DF00-4D42-B552-39511302113D),,,,,,
Form 1 (Advanced),,,,,,,,
Form 33 (InsydeH2O Setup Utility),,,,,,,,
Boot Configuration,,,,,,,,
*,0,8,1,Numlock,On,"Off,On","Selects Power-on state for Numlock","gif 9e=2 9d=1 and"
Form 41 (InsydeH2O Setup Utility),,,,,,,,
Video Configuration,,,,,,,,
GOP Configuration,,,,,,,,
*,0,115,1,GOP Driver,Enabled,"Enabled,Disabled","Enable GOP Driver will unload VBIOS; Disable it will load VBIOS","gif 9e=2 9d=1 and"
IGD Configuration,,,,,,,,
*,0,116,1,Integrated Graphics Device,Enabled,"Disabled,Enabled","Enable : Enable Integrated Graphics Device (IGD) when selected as the Primary Video Adaptor. Disable: Alwarys disable IGD","gif 9e=2 9d=1 and;sif f=2"
*,0,117,1,Primary Display,Auto,"Auto,IGD,PCIe","Select which of IGD/PCI Graphics device should be Primary Display","gif 9e=2 9d=1 and"
*,0,118,1,RC6(Render Standby),Enabled,"Enabled,Disabled","Check to enable render standby support","gif 9e=2 9d=1 and a3=1 |"
*,0,11a,1,PAVC,SERPENT Mode,"Disabled,LITE Mode,SERPENT Mode","Enable/Disable Protected Audio Video Control","gif 9e=2 9d=1 and"
*,0,1e5,1,DOP CG,Enabled,"Enabled,Disabled","Enable/Disable DOP Clock Gating","gif 9e=2 9d=1 and"
*,0,11b,1,GTT Size,2MB,"1MB,2MB","Select the GTT Size ","gif 9e=2 9d=1 and"
*,0,11c,1,Aperture Size,256MB,"128MB,256MB,512MB","Select the Aperture Size","gif 9e=2 9d=1 and"
*,0,11d,1,IGD - DVMT Pre-Allocated,64M,"64M,96M,128M,160M,192M,224M,256M,288M,320M,352M,384M,416M,448M,480M,512M","Select DVMT5.0 Pre-Allocated(Fixed) Graphics Memory size used by the Internal Graphics Device.","gif 9e=2 9d=1 and"
*,0,11e,1,IGD - DVMT Total Gfx Mem,256M,"128M,256M,MAX"," Select the size of DVMT 5.0 that the Internal Graphics Device will use","gif 9e=2 9d=1 and"
*,0,1d9,1,IGD Turbo,Auto,"Auto,Enabled,Disabled","Enable/Disable IGD Turbo","gif 9e=2 9d=1 and"
IGD - LCD Control,,,,,,,,
*,0,121,1,Force Lid Status,ON,"OFF,ON","For test: force to set lid status as on or off","gif 9e=2 9d=1 and"
*,0,123,1,ALS Support,Enabled,"Disabled,Enabled","Valid only for ACPI.","gif 9e=2 9d=1 and"
*,0,124,1,IGD Flat Panel,Auto,"Auto,640 x 480,800 x 600,1024 x 768,1280 x 1024,1366 x 768,1680 x 1050,1920 x 1200,1280 x 800",,"gif 9e=2 9d=1 and"
*,0,125,1,IGD Boot Type,Auto,"Auto,HDMI Port B,eDP","Selects preference for Integrated Graphics Device (IGD) display interface used when system boots.","gif 9e=2 9d=1 and"
*,0,1fa,1,MIPI DSI,Disabled,"Disabled,Enabled","Disable/enable MIPI DSI.","gif 9e=2 9d=1 and"
Form 35 (USB Configuration),,,,,,,,
*,0,134,1,XHCI Controller,Enabled,"Enabled,Disabled","Enable/Disable the USB XHCI PreBoot Support.

","gif 9e=2 9d=1 and 610=1 |"
*,0,135,1,xHCI Mode,Enabled,"Enabled,Disabled","Mode of operation of xHCI controller.



 Disable:Forces only USB 2.0 to be supported in the OS.

 Enable:Allows USB 3.0 to be supported in the OS and BIOS.

 Auto:This mode uses ACPI protocol to provide an option that enables the xHCI controller and reroute USB ports via the _OSC ACPI method call.

 Smart Auto:This mode is similar to Auto, but it adds the capability to route the ports to xHCI or EHCI according to setting used in previous boots (for non-G3 boot) in the pre-boot environment. This allows the use of USB 3.0 devices prior to OS boot.[This mode will be hidden when XHCI Controller setting Disable]","gif 9e=2 9d=1 and 610=1 |"
*,0,1ee,1,USB2 Link Power Management,Enabled,"Enabled,Disabled","Enable/Disable USB2 Link Power Management ","gif 9e=2 9d=1 and"
*,0,137,1,USB OTG Support,PCI Mode,"Disabled,PCI Mode","Enable/Disable USB OTG Support. 



In AUTO mode, OTG will only be enabled when Andriod OS selected.","gif 9e=2 9d=1 and"
*,0,147,1,USB VBUS,ON,"OFF,ON,Auto","VBUS should be ON in HOST mode. It should be OFF in OTG device mode.","gif 9e=2 9d=1 and"
*,0,138,1,EHCI Contorller,Disabled,"Enabled,Disabled","Control the USB EHCI (USB 2.0) functions.



One EHCI controller must always be enabled","gif 9e=2 9d=1 and 600=1 |"
*,0,142,1,USB RMH Mode,Enabled,"Disabled,Enabled","Enable/Disable PCH USB Rate Matching Hubs mode","gif 9e=2 9d=1 and 600=1 |"
*,0,1d6,1,USB EHCI debug,Disabled,"Disabled,Enabled","Enable/Disable PCH EHCI debug capability","gif 9e=2 9d=1 and 600=1 |"
*,0,139,1,USB Per-Port Control,Enabled,"Disabled,Enabled","Control each of the USB ports (0~9) disabling","gif 9e=2 9d=1 and"
*,0,13a,1,USB Port #0,Enabled,"Disabled,Enabled","Disable USB port","sif 24=0;gif 9e=2 9d=1 and"
*,0,13b,1,USB Port #1,Enabled,"Disabled,Enabled","Disable USB port","sif 24=0;gif 9e=2 9d=1 and"
*,0,13c,1,USB Port #2,Enabled,"Disabled,Enabled","Disable USB port","sif 24=0;gif 9e=2 9d=1 and"
*,0,13d,1,USB Port #3,Enabled,"Disabled,Enabled","Disable USB port","sif 24=0;gif 9e=2 9d=1 and"
Form 36 (Audio Configuration),,,,,,,,
Audio Configuration,,,,,,,,
*,0,148,1,LPE Audio Support,LPE Audio ACPI mode,"Disabled,LPE Audio PCI mode,LPE Audio ACPI mode","","gif 9e=2 9d=1 and"
*,0,149,1,Audio Controller,Disabled,"Disabled,Enabled","Control Detection of the Azalia device.



Disabled = Azalia will be unconditionally disabled



Enabled = Azalia will be unconditionally Enabled



Auto = Azalia will be enabled if present, disabled otherwise","gif 9e=2 9d=1 and;sif 2c=1"
*,0,14a,1,  Azalia VCi Enable,Enabled,"Disabled,Enabled","Enable/Disable Virtual Channel 1 of Audio Controller","sif 2a=0;gif 9e=2 9d=1 and"
*,0,14b,1,  Azalia Docking Support Enable,Disabled,"Disabled,Enabled","Enable/Disable Azalia Docking Support of Audio Controller","sif 2a=0;gif 9e=2 9d=1 and"
*,0,14c,1,  Azalia PME Enable,Enabled,"Disabled,Enabled","Enable/Disable Power Management capability of Audio Controller","sif 2a=0;gif 9e=2 9d=1 and"
*,0,14d,1,  Azalia HDMI Codec,Disabled,"Disabled,Enabled","Enable/Disable internal HDMI codec for Azalia","gif 9e=2 9d=1 and"
Form 37 (LAN Configuration),,,,,,,,
LAN Configuration,,,,,,,,
*,0,14e,1,LAN Controller,Disabled,"Enabled,Disabled","Enable/Disable onboard NIC","gif 9e=2 9d=1 and"
*,0,14f,1,  Wake on LAN Enable,Disabled,"Enabled,Disabled","Enable/Disable integrated LAN to wake the system","sif 2f=0;gif 9e=2 9d=1 and"
*,0,150,1,  SLP_LAN# Low on DC Power,Enabled,"Enabled,Disabled","Enable/Disable SLP_LAN# Low on DC Power","sif 2f=0;gif 9e=2 9d=1 and"
Form 38 (LPSS & SCC Configuration),,,,,,,,
*,0,151,1,LPSS & SCC Devices Mode,ACPI Mode,"ACPI Mode,PCI Mode","","gif 9e=2 9d=1 and"
SCC Configuration,,,,,,,,
*,0,1e1,1,SCC eMMC Boot Controller,Auto Detect,"Disable,Auto Detect,eMMC 4.41,eMMC 4.5","Disable/Select eMMC Boot mode; Auto Detect mode can switch the eMMC controller against the stepping","gif 9e=2 9d=1 and"
,0,1f9,1,eMMC Secure Erase,Disable,"Disable,Enable","Disable/Enable eMMC Secure Erase. When enabled, all the data on eMMC will be erased.",""
*,0,1dd,1,SCC eMMC45 Support,Enable,"Disable,Enable","Enable/Disable SCC eMMC 4.5 Support","gif 33=3 !"
*,0,1de,1,DDR50 Capability Support,Enable,"Disable,Enable","Enable/Disable SCC eMMC 4.5 DDR 50 support","gif 33=3 !"
*,0,1df,1,HS200 Capability Support,Enable,"Disable,Enable","Enable/Disable SCC eMMC 4.5 HS 200 support","gif 33=3 !"
*,0,1e0,1,Re Tune Timer Value,8,"0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15","Set the re tune timer value","gif 33=3 !;gif 36=1"
*,0,153,1,SCC SDIO Support ,Enabled,"Disabled,Enabled","","gif 9e=2 9d=1 and"
*,0,154,1,SCC SD Card Support,Enabled,"Disabled,Enabled","","gif 9e=2 9d=1 and"
*,0,1f6,1,SDR25 Capability Support for SDCard,Enabled,"Disabled,Enabled","","gif 9e=2 9d=1 and;gif 3a=1 !;gif 3c=1"
*,0,1f7,1,DDR50 Capability Support for SDCard,Disabled,"Disabled,Enabled","","gif 9e=2 9d=1 and;gif 3a=1 !;gif 3b=1"
*,0,155,1,MIPI HSI Support,Disabled,"Disabled,Enabled","Enable/Disable MIPI HSI Support 

 Note: Official BIOS cannot support MIPI display directly even you select enable here. MIPI VBT is specific to different panel, user need replace VBT manually.","gif 9e=2 9d=1 and"
*,0,1db,1,SCC SDIO Mode,Default,"Default,DDR50","Select SDIO mode.","gif 9e=2 9d=1 and"
LPSS Configuration,,,,,,,,
*,0,156,1,LPSS DMA #1 Support,Enabled,"Disabled,Enabled","","gif 9e=2 9d=1 and"
*,0,157,1,LPSS DMA #2 Support,Enabled,"Disabled,Enabled","","gif 9e=2 9d=1 and"
*,0,158,1,LPSS I2C #1 Support,Enabled,"Disabled,Enabled","","gif 9e=2 9d=1 and"
*,0,159,1,LPSS I2C #2 Support,Enabled,"Disabled,Enabled","","gif 9e=2 9d=1 and"
*,0,15a,1,LPSS I2C #3 Support,Enabled,"Disabled,Enabled","","gif 9e=2 9d=1 and"
*,0,15b,1,LPSS I2C #4 Support,Enabled,"Disabled,Enabled","","gif 9e=2 9d=1 and"
*,0,15c,1,LPSS I2C #5 Support,Enabled,"Disabled,Enabled","","gif 9e=2 9d=1 and"
*,0,15d,1,LPSS I2C #6 Support,Enabled,"Disabled,Enabled","","gif 9e=2 9d=1 and"
*,0,15e,1,LPSS I2C #7 Support,Enabled,"Disabled,Enabled","","gif 9e=2 9d=1 and"
*,0,15f,1,LPSS HSUART #1 Support,Enabled,"Disabled,Enabled","","gif 9e=2 9d=1 and"
*,0,160,1,LPSS HSUART #2 Support,Enabled,"Disabled,Enabled","","gif 9e=2 9d=1 and"
*,0,161,1,LPSS PWM #1 Support,Disabled,"Disabled,Enabled","","gif 9e=2 9d=1 and"
*,0,162,1,LPSS PWM #2 Support,Disabled,"Disabled,Enabled","","gif 9e=2 9d=1 and"
*,0,163,1,LPSS SPI Support,Disabled,"Disabled,Enabled","","gif 9e=2 9d=1 and"
I2C Devics Configuration,,,,,,,,
,0,1d8,1,I2C Touch Devic Address,Auto,"Auto,0x4B,0x4A","I2C Touch Address Select:

  RVP/iCDK(0x4B)

  FFRD(0x4A)",""
,0,1f4,1,SAR Sensor,Enabled,"Enabled,Disabled","Enable or Disable SAR sensor",""
Form 39 (Miscellaneous Configuration),,,,,,,,
Miscellaneous Configuration,,,,,,,,
*,0,164,1,HPET - HPET Support,Enabled,"Disabled,Enabled","High Performance Event Timer Support in Windows XP. Enabled this feature, the HPET table will be add-into ACPI Tables.","gif 9e=2 9d=1 and"
*,0,166,1,State After G3,S0 State,"S0 State,S5 State","Specify what state to go to when power is re-applied after a power failure (G3 state).","gif 9e=2 9d=1 and"
*,0,167,1,Clock Spread Spectrum,Disabled,"Disabled,Enabled","Enable Clock Chip's Spread Spectrum feature","gif 9e=2 9d=1 and"
*,0,168,1,UART Interface Selection,Internal UART,"Internal UART,SuperIO UART","Select which UART interface to use","gif 9e=2 9d=1 and"
*,0,169,1,PCU UART COM 1,Enabled,"Disabled,Enabled","Enable/Disable Onboard PCU UART COM 1","gif 9e=2 9d=1 and;sif 52=1"
*,0,1fc,1,BIOS Lock,Enabled,"Enabled,Disabled","Enable or Disable BIOS SPI region write protect.","gif 9e=2 9d=1 and"
*,0,1eb,1,ExI,Disabled,"Enabled,Disabled","Enabled/Disabled ExI","gif 9e=2 9d=1 and"
*,0,20e,1,H2OUVE Support,Disabled,"Disabled,Enabled","Enable/Disable interface for H2OUVE tool.","gif 9e=2 9d=1 and"
Form 40 (Security Configuration),,,,,,,,
TXE Configuration,,,,,,,,
*,0,16c,1,TXE,Enabled,"Disabled,Enabled","","sif a2=0;gif 9f=1 9e=2 9d=1 and | a1=1,2,3 |"
*,0,170,1,TXE HMRFPO ,Disabled,"Disabled,Enabled","","sif a0=0;gif 9f=1 9e=2 9d=1 and |"
*,0,171,1,TXE Firmware Update,Enabled,"Disabled,Enabled","","sif a0=0;gif 9f=1 9e=2 9d=1 and |"
*,0,16d,1,TXE EOP Message,Enabled,"Disabled,Enabled","Send EOP Message Befor Enter OS","sif a0=0;gif 9e=2 9d=1 and"
Platform Trust Technology,,,,,,,,
*,0,172,1,PTT ,Auto,"Disabled,Enabled,Auto","Enable/Disable PTT, 



In AUTO mode, PTT will only be enabled when WOS is selected.","gif 9e=2 9d=1 and"
*,0,1ed,1,Measured Boot,Enabled,"Disabled,Enabled","Enable/Disable Measured Boot","sif 5a=0"
TPM Configuration,,,,,,,,
*,0,177,1,Discrete TPM,Disabled,"Disabled,Enabled","","gif 9e=2 9d=1 and"
Form 42 (InsydeH2O Setup Utility),,,,,,,,
Chipset Configuration,,,,,,,,
ISP PCI Device Configuration,,,,,,,,
*,0,12a,1,ISP Enable/Disable,Enabled,"Enabled,Disabled","Enable/Disable ISP PCI Device Selection.","gif 9e=2 9d=1 and"
*,0,12b,1,ISP PCI Device Selection,ISP PCI Device as B0D3F0,"Disabled,ISP Device as subdevice of B0D2F0(IGD),ISP PCI Device as B0D3F0","Auto mode will set ACPI mode for Windows OS and PCI mode for Linux OS. Default ISP is PCI B0D2F0 for Window Boot. Linux Boot to select B0D3F0","gif 9e=2 9d=1 and 5d=0 and"
Form 43 (Thermal),,,,,,,,
Thermal Configuration Parameters,,,,,,,,
,0,202,2,IA_APPS_RUN,3400,"Step=100,Min=3000,Max=4000","Voltage in mV",""
,0,204,1,IA_APPS_CAP,5,"Step=1,Min=1,Max=99","Percentage",""
,0,205,1,USE IA_APPS_RUN or CAP,IA_APPS_RUN,"IA_APPS_RUN,IA_APPS_CAP","Use Voltage or Capacity to decide boot flow",""
,0,209,1,BatteryId DBI Base,240,"Step=10,Min=200,Max=250","Resistance in KOhms",""
,0,20a,1,BatteryId Analog Base,19,"Step=1,Min=15,Max=25","Resistance in KOhms",""
,0,20b,2,VBattery Threshold,3700,"Step=100,Min=3000,Max=4000","Voltage in mV for CPU Frequence Limit",""
,0,20d,1,CAP_Freq_Index,4,"Step=1,Min=0,Max=6","Index into CPU Frequency Table",""
,0,206,1,Boot on invalid battery,Enabled,"Enabled,Disabled","Allow to boot from invalid battery",""
*,0,178,1,Critical Trip Point,105 °C,"15 °C,23 °C,31 °C,39 °C,47 °C,55 °C,63 °C,71 °C,79 °C,85 °C,87 °C,90 °C,105 °C","This value controls the temperature of the ACPI Critical Trip Point - the point in which the OS will shut the system off.



NOTE:  100C is the Plan Of Record (POR) for all Intel mobile processors.","gif 9e=2 9d=1 and"
*,0,179,1,Passive Trip Point,85 °C,"15 °C,23 °C,31 °C,39 °C,47 °C,55 °C,63 °C,71 °C,79 °C,85 °C,87 °C,90 °C","This value controls the temperature of the ACPI Passive Trip Point - the point in which the OS will begin throttling the processor.","gif 9e=2 9d=1 and"
Dynamic Platform&Thermal Framework,,,,,,,,
*,0,17d,1,DPTF Feature,Enabled,"Disabled,Enabled","Enable/Disable DPTF, 



In AUTO mode, DPTF will only be enabled when WOS is selected.","gif 9e=2 9d=1 and"
DPTF T1 Sensor Participant,,,,,,,,
*,0,17e,2,Critical,70 °C,"25 °C,35 °C,40 °C,45 °C,50 °C,55 °C,60 °C,65 °C,70 °C,75 °C,80 °C,85 °C,90 °C,95 °C,100 °C,105 °C,110 °C,115 °C,120 °C,125 °C","Critical Temperature","gif 6d=0 9e=2 9d=1 and |"
*,0,180,2,Passive,60 °C,"25 °C,35 °C,40 °C,45 °C,50 °C,55 °C,60 °C,65 °C,70 °C,75 °C,80 °C,85 °C,90 °C,95 °C,100 °C,105 °C,110 °C,115 °C,120 °C,125 °C","Passive Temperature","gif 6d=0 9e=2 9d=1 and |"
DPTF Display Board Sensor Participant,,,,,,,,
*,0,182,2,Critical,60 °C,"25 °C,35 °C,40 °C,45 °C,50 °C,55 °C,60 °C,65 °C,70 °C,75 °C,80 °C,85 °C,90 °C,95 °C,100 °C,105 °C,110 °C,115 °C,120 °C,125 °C","Critical Temperature","gif 6d=0 9e=2 9d=1 and |"
*,0,184,2,Passive,43 C,"25 °C,35 °C,40 °C,43 C,45 °C,50 °C,52 C,55 °C,60 °C,65 °C,70 °C,75 °C,80 °C,85 °C,90 °C,95 °C,100 °C,105 °C,110 °C,115 °C,120 °C,125 °C","Passive Temperature","gif 6d=0 9e=2 9d=1 and |"
DPTF SOC Board Sensor Participant,,,,,,,,
*,0,186,2,Critical,81 C,"25 °C,35 °C,40 °C,45 °C,50 °C,55 °C,60 °C,65 °C,70 °C,75 °C,80 °C,81 C,85 °C,90 °C,95 °C,100 °C,105 °C,110 °C,115 °C,120 °C,125 °C","Critical Temperature","gif 6d=0 9e=2 9d=1 and |"
*,0,188,2,Passive,62 C,"25 °C,35 °C,40 °C,45 °C,50 °C,55 °C,60 °C,61 C,62 C,65 °C,70 °C,75 °C,80 °C,85 °C,90 °C,95 °C,100 °C,105 °C,110 °C,115 °C,120 °C,125 °C","Passive Temperature","gif 6d=0 9e=2 9d=1 and |"
DPTF Charger Board Sensor Participant,,,,,,,,
*,0,18a,2,Critical,78 C,"25 °C,35 °C,40 °C,45 °C,50 °C,55 °C,60 °C,65 °C,70 °C,75 °C,78 C,80 °C,85 °C,90 °C,95 °C,100 °C,105 °C,110 °C,115 °C,120 °C,125 °C","Critical Temperature","gif 6d=0 9e=2 9d=1 and |"
*,0,18c,2,Passive,55 °C,"25 °C,35 °C,40 °C,45 °C,50 °C,55 °C,55 °C,60 °C,61 C,65 °C,70 °C,75 °C,80 °C,85 °C,90 °C,95 °C,100 °C,105 °C,110 °C,115 °C,120 °C,125 °C","Passive Temperature","gif 6d=0 9e=2 9d=1 and |"
*,0,193,1,Super Debug,Disabled,"Disabled,Enabled","Super debug is for validation purpose","gif 6d=0 9e=2 9d=1 and |"
*,0,194,4,Processor Offlining,Disabled,"Disabled,Enabled","Enable or disable processor offlining, passive policy only","gif 9e=2 9d=1 and 6d=0 |"
*,0,198,4,Start P-State,P0,"P0,P1,P2,P3,P4,P5,P6,P7,P8,P9,P10,P11,P12","Instructs the policy when to initiate Active Core control if enabled","gif 9e=2 9d=1 and 6d=0 |"
*,0,19c,4,Step Size,25%,"25%,50%,75%","Instructs the policy to take away logical processors in the specified percentage steps","gif 9e=2 9d=1 and 6d=0 |"
*,0,1a0,4,Power Control Setting,Core Offlining,"Disabled,Core Offlining","Instructs the policy whether to use Core offliing if Active core control is enabled to be used in P0 or when power control is applied","gif 9e=2 9d=1 and 6d=0 |"
*,0,1a4,4,Performance Control Setting,Core Offlining,"Disabled,Core Offlining","Instructs the policy whether to use Core offliing if Active core control is enabled to be used in P1 or when performance control is applied","gif 9e=2 9d=1 and 6d=0 |"
*,0,1a8,1,DPPM,Enabled,"Disabled,Enabled","Control DPPM policy","gif 9e=2 9d=1 and 6d=0 |"
*,0,192,1,CLPM,OS level,"Disabled,Enabled,Appliccation specific,OS level","Current Low Power Mode","gif 9e=2 9d=1 and 6d=0 |"
*,0,1a9,1,DPTF Processor,Enabled,"Disabled,Enabled","Enable/Disable Processor Participant Device","gif 9e=2 9d=1 and 6d=0 |"
*,0,1aa,1,T1 Sensor,Disabled,"Disabled,Enabled","Enable/Disable T1 skin sensor","gif 9e=2 9d=1 and 6d=0 |"
*,0,1ab,1,Display Board Sensor,Enabled,"Disabled,Enabled","Enable/Disable Display Board skin Sensor","gif 9e=2 9d=1 and 6d=0 |"
*,0,1ac,1,SOC Board Sensor,Enabled,"Disabled,Enabled","Enable/Disable SOC Board skin Sensor","gif 9e=2 9d=1 and 6d=0 |"
*,0,1ad,1,Charger Board Sensor,Disabled,"Disabled,Enabled","Enable/Disable ULPMC Skin Temperature Sensor","gif 9e=2 9d=1 and 6d=0 |"
*,0,1ae,1,Ambient Temperature,Enabled,"Disabled,Enabled","Enable/Disable Ambient Temperature","gif 9e=2 9d=1 and 6d=0 |"
*,0,1ef,1,Ambient based Trip Point Change,Enabled,"Disabled,Enabled","This controls the Action part of the Ambient participant. When disabled, trip points would not be changed when Ambient participant notifies the FW of a new ambient temperature via _ATI.","gif 9e=2 9d=1 and 6d=0 |"
*,0,1f2,1,Allow higher performance on AC/USB,Enabled,"Disabled,Enabled","On AC/USB power source allow for higher performance and relax tablet skin temperature to higher limits. Warning: Note users may feel warm tablet skin.","gif 9e=2 9d=1 and 6d=0 |"
*,0,1af,1,Charger Participant,Enabled,"Disabled,Enabled","Enable/Disable Charger Participant Device","gif 9e=2 9d=1 and 6d=0 |"
*,0,1b0,1,Display Participant,Enabled,"Disabled,Enabled","Enable/Disable Display Participant Device","gif 9e=2 9d=1 and 6d=0 |"
*,0,1b1,1,Power Participant,Enabled,"Disabled,Enabled","Enable/Disable Power Participant Device","gif 9e=2 9d=1 and 6d=0 |"
Form 44 (System Component),,,,,,,,
PMIC Congfiguration,,,,,,,,
*,0,1b3,1,PMIC ACPI OBJECT,Enabled,"Disabled,Enabled","Enable/Disable PMIC ACPI Device.","gif 9e=2 9d=1 and"
System Power and Performance(PnP) Congfiguration,,,,,,,,
*,0,1b4,1,SoC PnP Setting,Auto Detect,"Disabled,Auto Detect,Ax Stepping,Bx Stepping","Select SoC PnP setting mode. Auto detect mode will load the SoC PnP table against stepping.","gif 9e=2 9d=1 and"
*,0,1e2,1,CFIO/GPIO PnP Setting,Enabled,"Disabled,Enabled","Enable/Disable CFIO/GPIO PnP setting mode. When enabled, CFIO/GPIO unused pins will be in tri-state for power saving.","gif 9e=2 9d=1 and"
*,0,1e3,1,LPC PnP Setting,Enable,"Disable,Enable","Enable/Disable LPC PnP Setting. When enabled, the Lpc will diable clock and be placed in tri-state for power saveing when Bios hands over control to OS. If there is device connected to LPC bus, this setting should not be enabled.","gif 9e=2 9d=1 and"
*,0,1f0,1,Asset SLP_S0IX_N in S0ix,Auto,"Disable,Enable,Auto","Auto/Enable/Disable Asset SLP_S0IX_N in S0ix. In Auto mode, PMC will assert SLP_S0IX_N ONLY for PR1.4 and beyond, FFRD8, RVP plus Rohm B3 or Dialog C0 or Maxim. In Enable mode, PMC will assert the SLP_S0IX_N to save power regardless the board type.","gif 9e=2 9d=1 and"
,0,201,1,Critical Battery Limit Feature,Disabled,"Disabled,Enabled","Enable or Disable Critical Battery Limit Feature.",""
,0,200,1,Critical Battery Limit,20,"Step=1,Min=1,Max=100","",""
Battery Charging Congfiguration,,,,,,,,
*,0,1b5,1,Battery solution,ULPMC solution,"Non ULPMC solution,ULPMC solution","If it does not match, battery will not work properly.","gif 9e=2 9d=1 and"
*,0,1d7,1,ULPMC Firmware Lock,Disabled,"Disabled,Enabled","Enable or Disable Lock ULPMC Firmware Update.","gif 9e=2 9d=1 and"
*,0,1dc,1,FSA ON,ON,"OFF,ON","FSA should be ON for PR1","gif 9e=2 9d=1 and"
*,0,207,1,PR1 MUX setting,Device Mode,"Device Mode,Host Mode","FFRD8 PR1 MUX setting option to switch between Host Mode and Device Mode","gif 9e=2 9d=1 and"
PSS Settings,,,,,,,,
,0,1e6,1,PSS Storage,Disabled,"Disabled,Enabled","Disable/Enable PSS-based secure boot",""
Lakemore Configuration:,,,,,,,,
,0,1e8,2,Memory Allocation Size,0   KB,"8   MB,4   MB,1   MB,128 KB,0   KB","Specify the amount of main memory to be reserved for Lakemore.  The memory will be allocated right after MRC initialization and its location will be stored into the Lakemore STOREMEMBAR registers.",""
,0,1ea,1,PDM/Dfx Setting,Power Save,"PDM On,Perf Mode,Power Save,Debug Reserved","PDM On: Enable PDM and keep Dfx powered.



Perf Mode: Disable PDM and keep Dfx powered. Allows more VISA signals to be used for HW debug.



Power Save: Disable PDM, turn off Dfx power and Visa clocks.



NOTE: If previous setting was POWERSAVE, then cold boot will be needed for Dfx to come back up.",""
*,0,1e7,1,PDM Msg Output,Disabled,"Disabled,Main Memory,IO - TBD","Configure VISA and Lakemore for PDM with the given output.



If MainMem is selected then be sure to allocate memory for the output msgs in the above setting.","sif 96=3 !"
,0,1f1,1,Enable DBG2 Table,Enabled,"Disabled,Enabled","Enable/Disable DBG2 ACPI Table for Windbg",""
,0,1f3,1,PM Weights,Enabled,"Enabled,Disabled","Enabled/Disabled PM Weights",""
,0,1fe,1,Droid Boot,Disabled,"Disabled,Enabled","Go to Droidboot to flash Android Image",""
,0,1ff,1,Android Boot,Disabled,"Disabled,Enabled","Boot android OS",""
,0,1fd,1,OS Selection,Android,"Windows 8.X,Android","OS Selection",""
FormSet Power (A04A27F4-DF00-4D42-B552-39511302113D),,,,,,
Form 1 (Power),,,,,,,,
*,0,1fb,1,S5 long run test,Disabled,"Disabled,Enabled","Enable : force to enable RTC S5 wake up, even if OS disables it. Support ipwrtest to do RTC S5 wakeup.","gif 10=2 f=1 and"
Form 64 (InsydeH2O Setup Utility),,,,,,,,
Advanced CPU Control,,,,,,,,
*,0,e8,1,Use XD Capability,Enabled,"Disabled,Enabled","Enable or disable processor XD capability","gif 10=2 f=1 and"
*,0,e7,1,Limit CPUID Max value,Disabled,"Disabled,Enabled","","gif 10=2 f=1 and"
*,0,ff,1,Bi-Directional PROCHOT#,Enabled,"Disabled,Enabled","When a processor thermal sensor trips(either core),the PROCHOT# will be driven.If bi-directional is enable ,external agents can drive PROCHOT# to throttle.","gif 10=2 f=1 and"
*,0,e9,1,VTX-2,Enabled,"Disabled,Enabled","","gif 10=2 f=1 and"
*,0,100,1,TM1 and TM2,Enabled,"Disabled,Enabled","Enable/Disable TM1/TM2","gif 10=2 f=1 and"
*,0,eb,1,Active Processor Cores,ALL,"ALL,1","Number of cores to enable in each processor package","gif 10=2 f=1 and"
*,0,101,1,P-States(IST),Enabled,"Disabled,Enabled","Enable processor performance states(P-States).","gif 10=2 f=1 and"
*,0,102,1,Boot Performance Mode,Max Performance,"Max Performance,Max Battery,Auto","Select the performance state that BIOS will set before OS handoff.","gif 10=2 f=1 and;sif 8=0"
*,0,ec,1,Turbo Mode,Auto,"Auto,Disabled,Enabled","Enable processor Turbo Mode(requires EMTTM enabled too).","gif 10=2 f=1 and;sif 8=0"
*,0,103,1,C-States,Enabled,"Disabled,Enabled","Enable processor idle power saving states(C-States).","gif 10=2 f=1 and"
*,0,ed,1,Max C-States,C7,"C7,C6,C1","Support the Max CPC State","sif b=0;gif 10=2 f=1 and"
,0,1b2,1,S0ix,Enabled,"Disabled,Enabled","Set platform to configure S0ix supported or not",""
*,0,1f5,1,AESNI Feature,Enabled,"Disabled,Enabled","Enable/Disable AESNI .","gif 10=2 f=1 and;sif 8=0"
FormSet Main (A04A27F4-DF00-4D42-B552-39511302113D),,,,,,
Form 1 (Main),,,,,,,,
FormSet Security (A04A27F4-DF00-4D42-B552-39511302113D),,,,,,
Form 1 (Security),,,,,,,,
*,0,e3,1,Current TPM Device,TPM 2.0,"Not Detected,TPM 2.0","Current TPM Device: TPM1.2, or TPM2.0.","gif true"
*,0,9d,1,TPM Availability,Availabile,"Availabile,Hidden","When Hidden, don’t exposes TPM to OS","sif 11b9=2 ! d=255 |;gif 4=2 5=1 and"
*,0,62,1,TPM Operation,No Operation,"No Operation,Disable,Enable","Enable:  Enable Storage and Endorsement Hierarchy. 

Disable:  Disable Storage and Endorsement Hierarchy.","sif 11b9=2 ! d=255 | 11bb=1 | c=1 |;gif 4=2 5=1 and"
*,0,68,1,Clear TPM,,,"Clear TPM. Removes all TPM context associated with a specific Owner.","sif 11b9=2 ! d=255 | 11bb=1 | c=1 |;gif 4=2 5=1 and b=1 |"
*,0,9f,1,Power on Password,Disabled,"Enabled,Disabled","Enable:System will ask input password on post time. Disable:System will ask input password when go to Setup Utility","sif 5=1 a=0 |"
FormSet Boot (A04A27F4-DF00-4D42-B552-39511302113D),,,,,,
Form 1 (Boot),,,,,,,,
*,0,6d,1,Quick Boot,Enabled,"Enabled,Disabled","Allows InsydeH2O to skip certain tests while booting. This will decrease the time needed to boot the system.","gif 17=2,3 16=1 and"
*,0,6e,1,Quiet Boot,Enabled,"Enabled,Disabled","Disables or enables booting in Text Mode.","gif 17=2,3 16=1 and"
*,0,e2,1,Power Up In Standby Support,Disabled,"Enabled,Disabled","Disable or enable Power Up In Standby Support.

 The PUIS feature set allows devices to be powered-up into the Standby power management state to minimize inrush current at power-up and to allow the host to sequence the spin-up of devices.","gif 17=2,3 16=1 and"
*,0,7d,2,Add Boot Options,Auto,"First,Last,Auto","Position in Boot Order for Shell,Network and Removables","gif 17=2,3 16=1 and"
*,0,60,1,ACPI Selection,Acpi5.0,"Acpi1.0B,Acpi3.0,Acpi4.0,Acpi5.0","Select booting to Acpi3.0/Acpi1.0B","gif 17=2,3 16=1 and"
*,0,5c,1,USB Boot,Enabled,"Enabled,Disabled","Disables or enables booting to USB boot devices.","gif 17=2,3 16=1 and"
*,0,75,1,EFI Device First,Enabled,"Disabled,Enabled","Determine EFI device first or legacy device first. If enable, it is EFI device first. If disable, it is Legacy device first.","gif 17=2,3 16=1 and"
*,0,65,1,UEFI OS Fast Boot,Enabled,"Enabled,Disabled","If enabled the system firmware does not initialize keyboard and check for firmware menu key.","sif 1=0,1;gif 17=2,3 16=1 and"
*,0,e1,1,  USB Hot Key Support,Enabled,"Disabled,Enabled","Enable/Disable to support USB hot key while booting. This will decrease the time needed to boot the system.","sif 1=0,1 7=1 |;gif 17=2,3 16=1 and"
*,0,69,2,Timeout,0,"Step=1,Min=0,Max=10","The number of seconds that the firmware will wait before booting the original default boot selection.","gif 17=2,3 16=1 and"
*,0,de,1,Automatic Failover,Enabled,"Disabled,Enabled","Enable: if boot to default device fail, it will directly try to boot next device.

Disable: if boot to default device fail, it will pop warning message then go into firmware UI.","gif 17=2,3 16=1 and"
Form 1338 (EFI),,,,,,,,
EFI,,,,,,,,
Form 1328 (Boot Device Priority),,,,,,,,
Boot Device Priority,,,,,,,,
*,0,76,1,Normal Boot Menu,Normal,"Normal,Advance","Select Normal Boot Option Priority or Advance Boot Option Priority","gif 17=2,3 16=1 and"
Form 1339 (Boot Type Order),,,,,,,,
Boot Type Order,,,,,,,,
Form 1330 (Hard Disk Drive),,,,,,,,
Hard Disk Drive,,,,,,,,
Form 1331 (CD/DVD-ROM Drive),,,,,,,,
CD/DVD-ROM Drive,,,,,,,,
Form 1329 (Floppy Drive),,,,,,,,
Floppy Drive,,,,,,,,
Form 1336 (Others),,,,,,,,
Others,,,,,,,,
Form 1332 (PCMCIA),,,,,,,,
PCMCIA,,,,,,,,
Form 1333 (USB),,,,,,,,
USB,,,,,,,,
Form 1334 (EMBED NETWORK),,,,,,,,
EMBED NETWORK,,,,,,,,
Form 1335 (BEV),,,,,,,,
BEV,,,,,,,,
FormSet Exit (A04A27F4-DF00-4D42-B552-39511302113D),,,,,,
Form 1 (Exit),,,,,,,,