U-Boot 2009.08-00066-g951a018 (Apr 30 2014 - 13:44:13) Avocent (0.0.3) EVB, Buil                                                                                            d: jenkins-idrac-yocto-release-483

CPU: SH-4A
BOARD: R0P7757LC00xxRL (C0 step) board
BOOT: Secure, HRK generated
DRAM:  240MB
  (240MB of 256MB total DRAM is available on U-Boot)
ENV:   Using primary env area.
In:    serial
Out:   serial
Err:   serial
PCIe:  Bridge loaded with 0x18000 bytes
WDT2:  Booted Lower Vector, 'uboot1'
sh_mmcif: 0, sh-sdhi: 1
Net:   sh_eth.0, sh_g_eth.0
INFO: 00:002 Start-up -to- util_idrac_main()
INFO: 00:005 U-Boot 2009.08-00066-g951a018 (Apr 30 2014 - 13:44:13) Avocent (0.0                                                                                            .3) EVB
INFO: 00:008 U-Boot checkin date(05-10-2013) Version(1.0.183)
INFO: 00:006 iDRAC PPID <NULL>
INFO: 00:003 SPI NOR init 4096 KiB MX25L3206E bus=0 cs=0, speed=1000000, mode=3
INFO: 00:007 SH-4A Product: Major Ver=0x31  Minor Ver=0x13 C3 Little endian
             Family=0x10    Major Ver=0x30  Minor Ver=0x0b
PASS: 00:016 Dedicated monolithic mgmt NIC disabled
INFO: 00:128 BCM54610 OUI=0x3fffff  Model=0x3f  Revision=0x0f PhyAddr=1
INFO: 00:007 SD CARD: is not found
sh_mmcif: Cmd(d'1) err
Card did not respond to voltage select!
INFO: 00:016 EMMC:   Device: sh_mmcif   Manufacturer ID: 0   OEM: 0
             Name:
INFO: 00:008 CPLD: Major Ver=0x1  Minor Ver=0x0  Maint Ver=0x3
             Planar: Type=0x02  Rev=0x8  Rework=0x0  Scratch/PathRetry=0x00
PASS: 00:014 Coin cell detected good,  AD=0x398 low water=0x2c1
PASS: 00:008 PCIe C0 Ver=0.15 MCTP en, CRC=0x8e9b6875 @0x8efbf954 cnt=0x18000
INFO: 00:007 Init PCIe mailbox(PCIe 0xFFEE0150=0x40010000)
INFO: 00:005 mode=normal
Erasing SPI flash at 0x100000...Writing to SPI flash...done
Erasing SPI flash at 0x110000...Writing to SPI flash...done
PASS: 01:152 Booted Lower Vector, 'uboot1' wdt2cnt=0
INFO: 00:005 wdt0cnt=0
PASS: 00:003 Clear CH1/CH2, clear 4K shared memory@0xffcaa000 on AC power up
PASS: 00:007 SMR0 no sermux env, default 0xd4
INFO: 00:005 GRACR=0x3c HISEL=0x00 SIRQCR5_D=0x03 SIRQCR6_D=0x01 LADMSK0=0xff2
             MRSTCR0=0xfedffe7f MRSTCR1=0xfff3ff0f MRSTCR2=0x7f80feff
             BARMAP=0x1 BCR=0x85000000 NCER=0x01fc NCMCR=0x0006 NCCSR=0x0303
PASS: 00:021 etherc0=90:B1:1C:43:48:3F
             getherc0=90:B1:1C:43:48:40
INFO: 00:009 Fan logic for monolithic planar type 2
             fan1 - def 0000 1fff 3d   fan2 - def 0000 1fff 3d
             fan3 - def 0000 1fff 3d   fan4 - def 0000 1fff 3d
             fan5 - def 0000 1fff 3d   fan6 - def 0000 1fff 3d
             fan7 - def 0000 1fff 3d   fan8 - def 0000 1fff 3d
INFO: 00:076 Env and backup CRC'ed ok
sh_mmcif: Cmd(d'1) err
Card did not respond to voltage select!
sh_mmcif: Cmd(d'1) err
Card did not respond to voltage select!
sh_mmcif: Cmd(d'1) err
Card did not respond to voltage select!
sh_mmcif: Cmd(d'16) err
set read bl len failed
*** fail to read block from device ***
*** can't read from device 1 ***
*** create default partitions ***
sh_mmcif: Cmd(d'1) err
Card did not respond to voltage select!
sh_mmcif: Cmd(d'16) err
set write bl len failed
*** fail to write block to device ***
*** can't write to device 1 ***
FAIL: 00:086 fwu_init() failure
INFO: 00:005 Sync eMMC/SPI NOR/Alternate u-boot images
FAIL: 00:005 ...eMMC/MBR does not have a bootable partition
FAIL: 00:005 verify_os_images(): eMMC/MBR does not have a bootable partition
FAIL: 00:008 Boot device=emmc  Boot partition-1/No bootable partition
             Boot Path Retry:P1/N=0 P5/N-1=0  Invalid boot partition
INFO: 00:014 Sync eMMC/SPI NOR/Alternate u-boot images
FAIL: 00:005 ...eMMC/MBR does not have a bootable partition
FAIL: 00:005 verify_os_images(): eMMC/MBR does not have a bootable partition
FAIL: 00:008 Boot device=emmc  Boot partition-1/No bootable partition
             Boot Path Retry:P1/N=0 P5/N-1=0  Invalid boot partition
INFO: 00:000 01:672


WDT2: Disabled


######################################################################
** No bootable iDRAC image is found **
** (System Health & ID LED is flashing amber at ~1/2 second rate).
To Recover iDRAC via an SD card.
1)  Format SD using FAT on a Windows box or EXT3 using Linux.
2)  Copy 'firmimg.d7' to root path.
3)  Insert SD card.
4)  System Health & ID button solid amber durning recover.
5)  Both boot paths are flashed.
######################################################################

Polling for SD card state change /