what is the next step?
USB Flashback that BIOS, then do whatever the guides you linked mentioned (installing that efi file I think) I’ve never done what you’re doing, so I can’t really help directly, I only know how to mod BIOS.
if I install the efi files now comes at the boot always wrong cpu
Then you may have wrong efi file? IS that one posted where they discussed your same or similar CPU or CPUID? Did you try this after using the BIOS I posted above at #16
Have you read all that thread yet? Those pages are VERY early in the thread, and I know last time I did this mod for someone else it was using a method much later in the thread and did not involve removing ucodes or using efi files.
So, that may be the early method, and different better method was found out later, at least that is what i think I remember about doing this mod for a few other people. But, it maybe just different for different series motherboards too, and that’s why i remember doing a much different edit?
have already tried a lot of files but always the same … I do not see right through there anymore 
Can you see the MultiCore Enhancement setting in your BIOS or not? You may have best luck, with old PRE v13 microcode (in there, or removed), with old BIOS and MCE setting made visible.
You may also need to use old ME FW, but which version I do not know.
MultiCore Enhancement is present
in the picture is just as a cpu as I have only that he is already on
the two picture is my cpu
I just found something out which I do not care about!
according to this page http://www.cpu-world.com/cgi-bin/CPUID.p…lter&STEPPING=1 my cpu has an id of an 8 core?
??
???
is there a possibility to fit the microcode on? as it stands on this pdf inside?https://newsroom.intel.com/wp-content/up…te-guidance.pdf
@wirkstoff - what are you wanting me to do with microcode exactly? I can put any microcode you want, just tell me what CPUID and what microcode revision you want.
And link me to the BIOS you want edited, or upload a copy etc
and this microcode is now registered exactly for my xeon cpu?
i have a xeon E5V3 cpu @hesswell-e!? for this cpu is not a microcode aviable
but the E5V4 is with microcode or you’ve done me now
according to intel tapelle my cpu should be exactly this
M1E5-2670 v30x306F22.3 / DDR4 2133 / 9.6120123021,2,3,7
Could you make me a bios times where things are unlocked? With amibcps you can make such changes?
I have no idea? I only did what you asked me to do. You need to give me the S-Spec or CPUID for you chip if you don’t know what microcode you need changed.
Sorry, nothing you say makes sense to me in regards to this. For changing microcode, I need to know exact CPU model, it’s CPUID, or it’s S-Spec so I can lookup the CPUID and change the correct microcode CPUID (To whatever version you want)
If you don’t know any of that, and can’t look at the IHS to get S-Spec, send me CPU-z dump.txt
The BIOS above only contains the exact change you asked me to do, that is why I said "Be specific, what do you want"
Yes, I can unlock BIOS, but lets sort this out first as your very confusing and we’ve been at this same thing for days/weeks now and still and same confused point. 
I want to drive my cpu with another id + microcode z.b. that my cpu can deal with sandybridge properties or something like that, so I thought that you just once make the microcode for 406 purely what my cpu could work with
that with the unlock menus in the bios I can even but if ic hdas bios save he always says something with signum and can not flashen it
You can only use microcode for your actual CPU
I can’t understand your second sentence at all, please explain that differently. Sounds like you mad mod BIOS but unsigned, so you can’t flash it?
If yes, open stock cap BIOS in UEFITool, extract body from capsule. Modify that. Then open stock cap BIOS in hex editor, in second tab, open your mod BIOS body.
On stock cap BIOS, go to 800h location, this is end of the capsule. Go to mod BIOS body, select all, copy, then go back to stock cap BIOS at 800h location, paste mod BIOS body, then save as USB Flashback name.cap and that is signed BIOS you can then flash with USB Flashback.
I have a cpu running with 306f1 but loud data on the internet, it is a 306f2 how do I get the 306f2 on this cpu?
could you remove all locks in my bios? that would be nice
I can get xcpm working with using FakeCPUID 0x040652, but only using this reboot fix:
reboot fix Sierra © Pike R. Alpha
Find: VUiJ5UFXQVZBVUFUU1BBidZBifdIiftFhf8PhA==
Replace: w5CJ5UFXQVZBVUFUU1BBidZBifdIiftFhf8PhA==
If I don’t have reboot fix, the boot is just stuck on:
OsxAptioFixDrv: Starting overrides for System\Library\CoreServices\boot.efi
Using reloc block: yes, hibernate wake: no
++++++++++++++++++++++++++++++++++++++++++++++
I have Asus X99-A patched using UEFIPatch.
AppleIntelInfo.kext v1.8c Copyright © 2012-2016 Pike R. Alpha. All rights reserved
Settings:
------------------------------------------
logMSRs…: 1
logIGPU…: 0
logCStates…: 1
logIPGStyle…: 1
InitialTSC…: 0xf07f05a4c7 (31 MHz)
MWAIT C-States…: 8480
Processor Brandstring…: Intel(R) Core™ i7-5820K CPU @ 3.30GHz
Processor Signature… : 0x306F2
------------------------------------------
- Family… : 6
- Stepping… : 2
- Model… : 0x3F (63)
Model Specific Registers (MSRs)
------------------------------------------
MSR_CORE_THREAD_COUNT…(0x35) : 0xFFFFFF803B2D9700
------------------------------------------
- Core Count… : 6
- Thread Count… : 12
MSR_PLATFORM_INFO…(0xCE) : 0x20080C3BF3812100
------------------------------------------
- Maximum Non-Turbo Ratio… : 0x21 (3300 MHz)
- Ratio Limit for Turbo Mode… : 1 (programmable)
- TDP Limit for Turbo Mode… : 1 (programmable)
- Low Power Mode Support… : 1 (LPM supported)
- Number of ConfigTDP Levels… : 1 (additional TDP level(s) available)
- Maximum Efficiency Ratio… : 12
- Minimum Operating Ratio… : 8
MSR_PMG_CST_CONFIG_CONTROL…(0xE2) : 0x400
------------------------------------------
- I/O MWAIT Redirection Enable… : 1 (enabled, IO read of MSR(0xE4) mapped to MWAIT)
- CFG Lock… : 0 (MSR not locked)
- C3 State Auto Demotion… : 0 (disabled/unsupported)
- C1 State Auto Demotion… : 0 (disabled/unsupported)
- C3 State Undemotion… : 0 (disabled/unsupported)
- C1 State Undemotion… : 0 (disabled/unsupported)
- Package C-State Auto Demotion… : 0 (disabled/unsupported)
- Package C-State Undemotion… : 0 (disabled/unsupported)
MSR_PMG_IO_CAPTURE_BASE…(0xE4) : 0x10414
------------------------------------------
- LVL_2 Base Address… : 0x414
- C-state Range… : 1 (C6 is the max C-State to include)
IA32_MPERF…(0xE7) : 0x777659587
IA32_APERF…(0xE8) : 0x9D297D497
MSR_FLEX_RATIO…(0x194) : 0xE0000
------------------------------------------
MSR_IA32_PERF_STATUS…(0x198) : 0x295200002D00
------------------------------------------
- Current Performance State Value… : 0x2D00 (4500 MHz)
MSR_IA32_PERF_CONTROL…(0x199) : 0xC00
------------------------------------------
- Target performance State Value… : 0xC00 (1200 MHz)
- Intel Dynamic Acceleration… : 0 (IDA engaged)
IA32_CLOCK_MODULATION…(0x19A) : 0x0
IA32_THERM_STATUS…(0x19C) : 0x88420000
IA32_MISC_ENABLES…(0x1A0) : 0x840089
------------------------------------------
- Fast-Strings… : 1 (enabled)
- Automatic Thermal Control Circuit… : 1 (enabled)
- Performance Monitoring… : 1 (available)
- Enhanced Intel SpeedStep Technology… : 0 (disabled)
MSR_TEMPERATURE_TARGET…(0x1A2) : 0x670A00
------------------------------------------
- Turbo Attenuation Units… : 0
- Temperature Target… : 103
- TCC Activation Offset… : 0
MSR_MISC_PWR_MGMT…(0x1AA) : 0x400000
------------------------------------------
- EIST Hardware Coordination… : 0 (enabled)
MSR_TURBO_RATIO_LIMIT…(0x1AD) : 0x22222D2D2D2D2D2D
------------------------------------------
IA32_ENERGY_PERF_BIAS…(0x1B0) : 0x0
MSR_POWER_CTL…(0x1FC) : 0x29040059
------------------------------------------
- C1E Enable…: 0
MSR_RAPL_POWER_UNIT…(0x606) : 0xA0E03
------------------------------------------
- Power Units… : 3 (1/8 Watt)
- Energy Status Units… : 14 (61 micro-Joules)
- Time Units … : 10 (976.6 micro-Seconds)
MSR_PKG_POWER_LIMIT…(0x610) : 0x7FFF80015FFF8
------------------------------------------
- Package Power Limit #1… : 4095 Watt
- Enable Power Limit #1… : 1 (enabled)
- Package Clamping Limitation #1… : 1 (allow going below OS-requested P/T state during Time Window for Power Limit #1)
- Time Window for Power Limit #1… : 10 (2560 milli-Seconds)
- Package Power Limit #2… : 4095 Watt
- Enable Power Limit #2… : 1 (enabled)
- Package Clamping Limitation #2… : 1 (allow going below OS-requested P/T state setting Time Window for Power Limit #2)
- Time Window for Power Limit #2… : 3 (20 milli-Seconds)
- Lock… : 0 (MSR not locked)
MSR_PKG_ENERGY_STATUS…(0x611) : 0x1E8F6FC
------------------------------------------
- Total Energy Consumed… : 1955 Joules (Watt = Joules / seconds)
MSR_PKG_POWER_INFO…(0x614) : 0x1280460
------------------------------------------
- Thermal Spec Power… : 140 Watt
- Minimum Power… : 0
- Maximum Power… : 0
- Maximum Time Window… : 0
MSR_PP0_POWER_LIMIT…(0x638) : 0x0
MSR_PP0_ENERGY_STATUS…(0x639) : 0x0
MSR_TURBO_ACTIVATION_RATIO…(0x64C) : 0x0
MSR_CONFIG_TDP_NOMINAL…(0x648) : 0x21
MSR_CONFIG_TDP_LEVEL1…(0x649) : 0x940000001E0460
MSR_CONFIG_TDP_LEVEL2…(0x64a) : 0x94000000000000
MSR_CONFIG_TDP_CONTROL…(0x64b) : 0x0
MSR_TURBO_ACTIVATION_RATIO…(0x64c) : 0x0
MSR_PKGC6_IRTL…(0x60b) : 0x0
MSR_PKG_C2_RESIDENCY…(0x60d) : 0x0
MSR_PKG_C6_RESIDENCY…(0x3f9) : 0x0
IA32_TSC_DEADLINE…(0x6E0) : 0xF0820FFEF1
CPU Ratio Info:
------------------------------------------
Base Clock Frequency (BLCK)… : 100 MHz
Maximum Efficiency Ratio/Frequency…: 12 (1200 MHz)
Maximum non-Turbo Ratio/Frequency…: 33 (3300 MHz)
Maximum Turbo Ratio/Frequency…: 45 (4500 MHz)
P-State ratio * 100 = Frequency in MHz
------------------------------------------
CPU C6-Cores [ 0 1 2 3 4 5 6 7 8 9 10 11 ]
CPU P-States [ (12) 23 26 27 28 29 30 31 32 34 35 36 37 38 39 40 41 42 43 44 45 ]