@SoniX
Thank you for the 1.40!!!
I ve a issue concerning the Efi Intel Gigabyt UNDI, if i start with previously modded bios (U1), the module still remain to 0.0.07, if i use original bios (U2), all run fine.
EDIT: Chipset X79, Intel 82579, in my Bios (installed) it’s still 0.0.07 with the modded one, and 0.0.09 with the original one.
Ghostearth.
@ Ghostearth
Yes, for BIOS Aptio4, if you have already installed version 0.0.07 to version 0.0.09 update until you get. Over time, I decide this issue.
Use original BIOS.
I have just downloaded the new version 1.40 and will use it in the next few days, thank you. 
@Sonix
I have used UBU v1.40 and observed that when updating (Option 3, then Sub Option 1) the EFI Intel PRO/1000 UNDI v6.0.24 , UBU tool updates to EFI Intel Gigabit UNDI v 0.0.69 instead of EFI Intel PRO/1000 UNDI v6.9.07 or 6.6.04.
Is it normal ?
Here is the screenshot:
@ 100PIER
Sabertooht X99 - onboard 2 NIC:
LAN
1) ! - Intel® I218V, 1 x Gigabit LAN Controller(s)
2) Realtek® 8111GR, 1 x Gigabit LAN
Since there is one on board LAN controller i218-V, then it must be renewed Gugabit UNDI version 0.0.09.
Rule updating Intel LAN:
If onboard 1 NIC 82579/217/218/219 - Gigabit UNDI v0.0.09 (for Aptio 4 Boot Agent CL v0.1.05)
If onboard 1 NIC 210/211/350 - PRO/1000 UNDI v6.9.07 (for Aptio 4 Boot Agent GE v1.5.72)
If onboard 2 NIC 82579/217/218/219 + 210/211/350 and 1 EFI module - PRO/1000 UNDI v6.6.04 (for Aptio 4 Boot Agent CL v0.1.05 and Boot Agent GE v1.5.72)
If onboard 2 NIC 82579/217/218/219 + 210/211/350 and 2 EFI module - Gigabit UNDI v0.0.09 + PRO/1000 UNDI v6.9.07
My motherboard (Z77) has 1 nic 82579, but ubu 1.40 does not update to UNDI v0.0.09, it stays at 0.0.07 version (previously moded with ubu 1.37).
Yes. SKL 06E3 - 4A
Thank you.
Did I miss something? UBU can now update X99 Aptio V? So it should work even on Z170?
Yes, perhaps only a partial update.
For some reason, my one onboard I210 updates from UNDI 6.0.24 to UNDI 0.0.09. Shouldn’t it be updating to 6.9.07? On Aptio V.
If only one network controller i210, the upgrade should be up to version 6.9.07.
Specify the a model board and BIOS.
Thanks for the reply.
I have an MSI X99S-MPOWER BIOS vM.71
hello to everyone.
i’m a new member and after reading a lot of discussion i decide to register me.
i have a little problem updating bios of my sabertooth x99.
i would like to update it with irst version 14 for nvme support to create raid with 2 sm951 nvme
the ubu works good, it update the driver, but the file that ubu create is not recognized from the ez asus bios updater.
anyone can help me?
thank you
Parrotts
p.s.
sorry for bad english
I installed this yesterday and it appears to give us SGX instructions, 3A didn’t have those. Both AIDA and HWInfo show this.
hi
thank you for the rreplay
today i’ve
update the bios with usb bios flash and it works but istill having problem with raid setup
i’m trying to install 2 sm951 nvme in radi 0 on my sabertooth x99 and i have some difficult to do.
the ssd is installed one in m.2 native slot and one in a pcie adaptor in the second slot.
bios see both.
i can install os in both.
i modded bios file to update with version 14 of intel rst driver ( in fact in the advanced mode of bios in intel rapid storage flag it shown version 14 but no disc is detected)
in the nvme configuration they are listed
bus 3 sm951…
bus 5 sm951…
but the irst don’t see that unit
wath i’ve missed to do?